How To Fix Laptop Power Jack Without Soldering? If your laptop does not charge when you rotate or tilt the charging pin, or even when it is detected, it is because you are using the incorrect charger cable, connector, or DC jack (inside the laptop).
However, how do you determine whether the issue is with your laptop or charger? You will get all of the answers to your questions if you read this post.
I’m sure you’ve arrived on this page to learn How To Fix Laptop Power Jack Without Soldering. Unfortunately, this is not frequently possible because the majority of laptops’ power jacks are soldered directly to the motherboard, necessitating the use of a hot soldering iron to repair.
Prior to beginning the essential repair process, you should be aware of the following:
How To Fix Laptop Power Jack Without Soldering
By and large, the majority of laptop chargers operate on these two alerts: + VE and GND. On the other hand, some manufacturers, similar as Dell, include an additional sensor pin in addition to these positive and negative connections. As a result, the laptop’s jack features three contacts.
As you can see in the images above, these DC-jacks are wired to the connector that connects to the motherboard. In this scenario, there are a few non-soldering options for repairing the laptop’s power jack. Now, take a look at the DC jack image below, which is soldered directly to the motherboard, and without soldering, you cannot do anything.
We’ve now begun the process of repairing the damage step by step.
CHECK YOUR LAPTOP ADAPTER
As I previously stated, how do we know that the issue is with our laptop’s DC jack and not the charger?
If DC Jack has suffered bodily damage, there is no requirement for an explanation to convict him.
However, testing your laptop adapter is simple. To begin, connect the laptop charger to the wall outlet and verify the output voltage. It should appear to be printed on the body of a charger.
If you are obtaining the correct voltage, your laptop has a serious problem. However, this is not a comprehensive confirmation that your laptop charger is working properly; I will also soon provide a guide on how to repair the laptop charger.
CHECK WHAT PROBLEM YOU ARE HAVING?
I’ve seen numerous posts that focus on simply repairing a special one for laptop jacks, which won’t work for everyone. Yes! Numerous issues can occur with DC Jack; you must first recognise them before attempting to resolve them, as they all have unique solutions. For instance:
- The facility jack’s inner pins are fractured.
- The entire jack has been damaged.
- When connected, the DC-in jack generates several sparks and becomes quite hot.
- DC Jack stepped from the laptop.
- The track on the motherboard that links the jack to the circuit is damaged.
- When the charger pin is plugged in, the laptop jack’s pin turns on the motherboard.
- As you can see, the laptop DC jack is unable to obtain any information regarding any soldering/repair process. I’m presenting each significant issue and its answer separately; you can find and resolve your own difficulty.
#1: PROBLEMS INVOLVING PHYSICAL DESTRUCTION
As indicated previously, if a pin or the entire jack of your laptop is broken, there is no way to repair it; it must be replaced. Some may even urge that you stick with anything different; I strongly advise against this.
A soft connection between the DC jack and adapter pin prevents current flow and causes heat. This can permanently harm the laptop charger pin or the editor board, so you’d be wise to replace it.
Now unplug the DC in-jack connector from the motherboard and unscrew it from the body. If the jack board is soldered directly to it, gently and carefully remove it, as this might cause significant damage to the circuit tracks.
#2: PROBLEMS WITH THE TRACKS, PINS, AND WIRES ON THE MOTHERBOARD
If the DC jack is functional and appears to be in good condition physically, we can repair it and restore power to our laptop.
SECTION 1: THE DC IN-JACK HAS A SEPARATE CONNECTOR FOR THE MOTHERBOARD
To begin, unplug the jack connector from the motherboard and reconnect it to the DC jack using the adaptor. Now check the voltage on the facility jack connectors; there should be none.
To fix this:
Identify a broken wire or disconnection on a damaged DC jack, reconnect it properly, and sell it. You can also utilise heat shrink tubes for reinforcement if you have them.
Verify the voltage. As you made the connection, it should be present.
Reconnect all of the cables and reassemble the laptop.
SECTION 2: DC IN JACK IS SOLD ON THE MOTHERBOARD
In comparison to the preceding procedure, this one demands a bit extra caution due to the fact that we will be working on the motherboard. Thus, the scenario is as follows:
DC JACK IS SPINNING
This issue is caused by dry soldering, which is exacerbated by our continual strength. To repair it, apply flow to all of the jack’s pins and re-solder it properly.
THE MOTHERBOARD TRACK IS BURNED OUT, OR A PIN IS BROKEN.
As can be seen physically, this repair requires some prerequisite abilities, as an erroneous connection can render your laptop unusable. To correct this, first determine which track is burned; is it + VE, GND, or a sensing signal? Then connect the jack pin straight to the path.
Apply hot glue or an epoxy combination to keep it from spoiling again. It acts as a blanket joint between the motherboard and the adapter, allowing it to survive instances where the adapter is backed and forth.
Use a thick copper wire to avoid burning, and avoid allowing the glue to penetrate the DC connector.
FAQS – How To Fix Laptop Power Jack Without Soldering
Can a laptop charging port be fixed?
To repair the laptop charging port, you must first determine the root of the issue. If the power jack is attached to the motherboard, it is simple to remove and replace. On the other hand, if the power jack is damaged, you must deliver it and replace it with a new one.
How do I know if my laptop battery or charger is bad?
You can determine whether or not the charger is defective by examining the charging indications on the laptop. Additionally, you can discover a bad battery by running software or by noticing that the laptop only starts when connected to the charger.
Can I leave my laptop plugged in overnight?
Some PC makers state that it is acceptable to leave the laptop plugged in at all times, while others provide specific reasons why this is not acceptable. Apple previously recommended charging and draining laptop batteries at least once a month.
Can you power a laptop without a power cord?
The quickest and most convenient way to accomplish this is with a universal adapter. Whatever way of charging you choose, don’t forget to check the voltage. If that is not an option for you, you can still power your laptop using a car battery or an external battery charger.
Conclusion
We hope you’ve discovered all of the information you’re looking for on How To Fix Laptop Power Jack Without Soldering.
We appreciate your visit to CartsVella! If you found this article useful, or if you have any questions about it, please contact us. Kindly leave a remark below. We’ll contact you shortly.
